Rear springs
5 posters
Page 1 of 1
Rear springs
I'm getting ready to get the new springs for my 75 Malibu. It sits decent but the rear is too high for me. I was thinking about the eibach sport set up for the 95 Impala SS but the research I'm doing leads me to see that it is only a 1.2 inch drop from stock. I need the rear to come down a full 2 inches. I see where OPGI has a 1,2 and a 3 inch drop spring. Anyone have experience with those? I read the build thread for the Sean Rich's car and he posted he used the OPGI 2 inch set up but who knows in the pages and pages of postings if he did anything else. I don't want it too low but I'm afraid I'll end up with a rake when I want the car to sit level.
Damon23- G3GM Member
- Street Cred : 5
Re: Rear springs
Never tried them. But might be worth a shot. Adjustable up to 2 inches.
http://www.speedwaymotors.com/Universal-Lift-Lower-Coil-Spring-Control-Kit,67863.html
http://www.speedwaymotors.com/Universal-Lift-Lower-Coil-Spring-Control-Kit,67863.html
Joe73- Donating Member
- Street Cred : 83
Re: Rear springs
I personally would not use those. I've heard they weaken the springs. But you just never know.
fasrnur- G3GM Enthusiast
- Street Cred : 9
Re: Rear springs
This thread has some pics. G3Nut installed the OPGI rear springs as well. I had the Bell Tech's installed (front and back) and I didn't like them for the rear. I had a rake from front to back.
I'm still trying to figure out what lowering springs to install.
https://www.g3gm.com/t10701-need-advice-from-those-that-lowered
I'm still trying to figure out what lowering springs to install.
https://www.g3gm.com/t10701-need-advice-from-those-that-lowered
Hawk03- G3GM Enthusiast
- Street Cred : 18
Re: Rear springs
I think I'm going to go with the OPGI 2 inch drop for the rear. If that does not work then I'll try the 3 inch.
Damon23- G3GM Member
- Street Cred : 5
Re: Rear springs
I did 2" Belltech drop springs front and back on my SS a few years back. It rode great and handled well for a 4000 pound plus vehicle.
g3chevy / Mr Pontiac- Donating Member
- Street Cred : 34
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Wed May 08, 2024 8:11 am by Mitchell Murphy
» 1973 Chevelle SS, 350, 4spd. build
Wed May 08, 2024 8:09 am by Mitchell Murphy
» Who works on 73-77 "soft" steering wheels?
Tue May 07, 2024 12:46 pm by relic7680
» Blue door jamb sticker
Sun May 05, 2024 3:10 pm by Joe73
» Factory am/fm
Sun May 05, 2024 6:22 am by Joe73
» Painting Interior Plastic
Thu May 02, 2024 10:43 am by 76Chevelle2Tone
» Need driver side bucket seat 73 Laguna
Tue Apr 30, 2024 9:44 pm by Limey SE
» triangle stainless window trim
Sun Apr 28, 2024 2:04 pm by 454fourspeedss
» door interior trim retainer clips
Sat Apr 27, 2024 8:29 pm by Limey SE
» Rusty's progress motor Parts arrived LOL Half are on
Sat Apr 27, 2024 12:25 pm by bracketchev1221