Running 10:1 compression
4 posters
G3GM :: G3 Tech :: Engine & Driveline
Page 1 of 1
Running 10:1 compression
What are my options for running a compression ratio this high.
I know everyone recommends 9:1 for the street.
My actual math from my engine calculations = 9.78:1
Chevy 396
Bore 4.124
Stroke 3.766
cylinder head volume 118cc
Pistons TRW L2242f30
Dome height .335
dome volume -38.30
deck clearance .025 ???
Gasket thickness .040
__________________
I know everyone recommends 9:1 for the street.
My actual math from my engine calculations = 9.78:1
Chevy 396
Bore 4.124
Stroke 3.766
cylinder head volume 118cc
Pistons TRW L2242f30
Dome height .335
dome volume -38.30
deck clearance .025 ???
Gasket thickness .040
__________________
Sinister- G3GM Member
- Street Cred : 0
Re: Running 10:1 compression
I dont see a problem with 10:1 at all. Yes, you will have to retard the timing a bit but it wont be a problem. All my buddies all shoot for 10:1 when building their motors.
Joe73- Donating Member
- Street Cred : 83
Re: Running 10:1 compression
Your camshaft will play an important role if you plan to run that kind of compression on pump gas. You are looking at "static" compression. As long as your "dynamic" compression is around 7.5:1 or no more than about 8:1 you will be fine. I could go on for a while about the subject, but google is your friend. Also check some earlier posts about cam selection on this site. I want to say I went into detail about dynamic vs static on a couple of threads.
The Dude- Management
- Street Cred : 48
Re: Running 10:1 compression
I do mix my own racing fuel...110 octane mixed with pump gas,but I don't want to rebuild this motor again.
Any cam recommendations would be great.
I'll probably go hydraulic with rhoads lifters,or maybe even solid cam.
No thanks to the roller crowd,I'd rather buy hard parts for $1000.
Any cam recommendations would be great.
I'll probably go hydraulic with rhoads lifters,or maybe even solid cam.
No thanks to the roller crowd,I'd rather buy hard parts for $1000.
Sinister- G3GM Member
- Street Cred : 0
Re: Running 10:1 compression
Had a 406 in my '77 Elco, which calculated to 9.8:1, and it sure didn't like anything except premium gas. Ran real good on 100 low-lead avgas. That same engine, 408 now, is now in the Malibu, but with less CR, because of pistons with 4 valve notches instead of 2 on the pistons. It runs OK on mid-grade now. Same 280 cam on both rebuilds.
pila- Donating Member
- Street Cred : 43
Similar topics
» Rochester 2GC running lean
» 383 in and running. Now the question?
» Show us what your running in your ride
» 383 in and running. Now the question?
» Show us what your running in your ride
G3GM :: G3 Tech :: Engine & Driveline
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Today at 2:56 pm by Limey SE
» Painting Interior Plastic
Yesterday at 11:52 am by Joe73
» Anyone good at photoshop?
Wed Apr 24, 2024 9:37 pm by 76 Malibu
» El Camino/Sprint LH Aftermarket Quarter Panel FOR SALE
Wed Apr 24, 2024 5:18 am by relic7680
» 1973 chevelle four speed console
Sun Apr 21, 2024 10:32 pm by Limey SE
» dashes
Sun Apr 21, 2024 10:26 pm by Limey SE
» Used OEM Hood 73-77
Fri Apr 19, 2024 2:46 pm by 73 ss wgn
» 76 Laguna parked in 2002
Sun Apr 07, 2024 1:32 pm by Limey SE
» Thanks for having me
Wed Mar 27, 2024 7:25 pm by 77camino
» 77 elco SS
Tue Mar 26, 2024 4:35 pm by Whisperer