383 in and running. Now the question?
+8
dynchel
Tom77
bracketchev1221
pila
jerry46765
ant7377
Limey SE
JB2wheeler
12 posters
G3GM :: G3 :: General Discussion
Page 1 of 1
383 in and running. Now the question?
by Tom77 Sat 10 May 2014 - 17:23
Never had engine with aluminum heads. I put rubber ribbed valve cover gaskets on and they leak like a siv. What do you all use? It looks like it's coming right through the bolt holes.
Tom77- Donating Member
- Street Cred : 9
Re: 383 in and running. Now the question?
by JB2wheeler Sat 10 May 2014 - 18:29
I'll bet you use synthic oil. JB
JB2wheeler- G3GM Fanatic
- Street Cred : 28
Re: 383 in and running. Now the question?
by Limey SE Sat 10 May 2014 - 18:36
Ghost Rider wrote:Never had engine with aluminum heads. I put rubber ribbed valve cover gaskets on and they leak like a siv. What do you all use? It looks like it's coming right through the bolt holes.
These are what most of my friends have used on ALum Heads
http://www.ebay.com/itm/FEL-PRO-FELPRO-HEAD-GASKETS-FOR-ALUMINUM-HEADS-Z-1003-2-/331139390523?pt=Motors_Car_Truck_Parts_Accessories&hash=item4d19721c3b&vxp=mtr
Limey SE- Management
- Street Cred : 97
Re: 383 in and running. Now the question?
by Tom77 Sat 10 May 2014 - 19:02
JB2wheeler wrote:I'll bet you use synthic oil. JB
No believe it or not they suggested Rotella with Lucas break in treatment.
Tom77- Donating Member
- Street Cred : 9
Re: 383 in and running. Now the question?
by Limey SE Sat 10 May 2014 - 19:21
dynchel wrote:He asked about valve covers , not head gaskets.Limey wrote:Ghost Rider wrote:Never had engine with aluminum heads. I put rubber ribbed valve cover gaskets on and they leak like a siv. What do you all use? It looks like it's coming right through the bolt holes.
These are what most of my friends have used on ALum Heads
http://www.ebay.com/itm/FEL-PRO-FELPRO-HEAD-GASKETS-FOR-ALUMINUM-HEADS-Z-1003-2-/331139390523?pt=Motors_Car_Truck_Parts_Accessories&hash=item4d19721c3b&vxp=mtr
OHH snap how did I miss that LOL
Limey SE- Management
- Street Cred : 97
Re: 383 in and running. Now the question?
by Tom77 Sat 10 May 2014 - 19:29
If I were leaking from there I would shoot myself!
Tom77- Donating Member
- Street Cred : 9
Re: 383 in and running. Now the question?
by dynchel Sat 10 May 2014 - 19:58
I wish I could offer advise, but I have iron heads. Â I've never heard of this problem, do you have spreader bars? Â That stopped my old chrome covers from leaking.
dynchel- Donating Member
- Street Cred : 40
Re: 383 in and running. Now the question?
by pila Sat 10 May 2014 - 21:54
What type valve covers ? The cast aluminum type usually solve the leak problems that the stamped steel type sometimes have.
You might be able to slip O rings on/under the heads of the bolts (?)
You might be able to slip O rings on/under the heads of the bolts (?)
pila- Donating Member
- Street Cred : 43
Re: 383 in and running. Now the question?
by Tom77 Sun 11 May 2014 - 5:31
I do have chrome valve covers with the spreader bars. Only put permatex on top side of gasket to hold. Should I do both?
Tom77- Donating Member
- Street Cred : 9
Re: 383 in and running. Now the question?
by ant7377 Sun 11 May 2014 - 6:49
Ive had better luck using studs rather than bolts to hold the valve covers down. Try using cork gasket too. They seem to seal better. They make thick ones,I think Fel Pro makes them. Might even have them over the counter and Auto Zone or Advanced.
ant7377- G3GM Addict
- Street Cred : 36
Re: 383 in and running. Now the question?
by bracketchev1221 Sun 11 May 2014 - 7:16
I am using summit steel frame reusable rubber gaskets on mine with wing nuts and studs instead of bolts. Â Don't glue them to anything. I have airflow research aluminum heads on mine.
bracketchev1221- G3GM Enthusiast
- Street Cred : 15
Re: 383 in and running. Now the question?
by dynchel Sun 11 May 2014 - 8:26
I've always used studs with wing nuts & spreader bars and never had problem. Â Currently I have thick flange m/t covers that won't accept the spreaders but no leak issues. Â Make sure the bolts have never been over tightened and the flange is straight (I've seen plenty where the cover is peened around the bolts, this will leak every time)
dynchel- Donating Member
- Street Cred : 40
Re: 383 in and running. Now the question?
by Dinomyte Sun 11 May 2014 - 19:36
Cork is your friend, with spreader bars.
Ribbed ? Got a picture?
But take the covers off and look at the holes for peening as Dynchel said, and also make sure the gasket didn't slip off. Â I had that happen once, there was just enough for it to seal at the start but finally worked it's way out from between the head and the valve cover.
good luck.
Ribbed ? Got a picture?
But take the covers off and look at the holes for peening as Dynchel said, and also make sure the gasket didn't slip off. Â I had that happen once, there was just enough for it to seal at the start but finally worked it's way out from between the head and the valve cover.
good luck.
Dinomyte- Donating Member
- Street Cred : 11
Re: 383 in and running. Now the question?
by Tom77 Sun 11 May 2014 - 19:59
Ok put in Edlebrock gaskets. They held for the 20 minute burn in at 2000 rpm. Took it for a short ride. My foot accidentally slipped to the floor(LOL) it started smoking again. Got back to the garage and they were leaking again. Looks like I'll be taking them off one more time.
Tom77- Donating Member
- Street Cred : 9
Re: 383 in and running. Now the question?
by jerry46765 Sun 11 May 2014 - 21:07
Center bolt or perimeter type covers? It's leaking around the bolts? I thought center bolt had a o-ring on each bolt?
jerry46765- Donating Member
- Street Cred : 20
Re: 383 in and running. Now the question?
by chevellelaguna Sun 11 May 2014 - 21:18
I've reused the same cork valve cover gaskets for the past 17 years, even reused them multiple times when Swapping to different valve cover styles. No leaks, no problems.
chevellelaguna- G3GM Enthusiast
- Street Cred : 16
Re: 383 in and running. Now the question?
by pila Mon 12 May 2014 - 0:58
Not sure about your covers, but may folks have leak problems with chromed covers for some reason.
I have a pair, that came on my '74 Malibu when I bought it in 1990. I can't seem to give them away. Different engine since then...
I have a pair, that came on my '74 Malibu when I bought it in 1990. I can't seem to give them away. Different engine since then...
pila- Donating Member
- Street Cred : 43
Re: 383 in and running. Now the question?
by bracketchev1221 Mon 12 May 2014 - 5:44
I assume this engine has a PCV valve and a breather on opposite valve covers?
bracketchev1221- G3GM Enthusiast
- Street Cred : 15
Re: 383 in and running. Now the question?
by Tom77 Mon 12 May 2014 - 7:12
OK biting the bullet. Ordered the aluminum covers with the t handle bolts will install with cork gaskets dry correct?
Tom77- Donating Member
- Street Cred : 9
Re: 383 in and running. Now the question?
by Tom77 Sun 18 May 2014 - 7:27
{\rtf1\ansi\ansicpg1252
{\fonttbl\f0\fnil\fcharset0 ArialMT;}
{\colortbl;\red255\green255\blue255;\red0\green0\blue0;\red255\green255\blue255;}
\deftab720
\pard\pardeftab720\partightenfactor0
\f0\fs22 \cf2 \cb3 \expnd0\expndtw0\kerning0
\outl0\strokewidth0 \strokec2
}{\rtf1\ansi\ansicpg1252
{\fonttbl\f0\fnil\fcharset0 ArialMT;}
{\colortbl;\red255\green255\blue255;\red0\green0\blue0;\red255\green255\blue255;}
\deftab720
\pard\pardeftab720\partightenfactor0
\f0\fs22 \cf2 \cb3 \expnd0\expndtw0\kerning0
\outl0\strokewidth0 \strokec2}{\rtf1\ansi\ansicpg1252
{\fonttbl\f0\fnil\fcharset0 ArialMT;}
{\colortbl;\red255\green255\blue255;\red0\green0\blue0;\red255\green255\blue255;}
\deftab720
\pard\pardeftab720\partightenfactor0
\f0\fs22 \cf2 \cb3 \expnd0\expndtw0\kerning0
\outl0\strokewidth0 \strokec2}[url=https://servimg.com/view/17916191/77][im. Thanks for all the help aluminum covers with dry cork did the trick.
{\fonttbl\f0\fnil\fcharset0 ArialMT;}
{\colortbl;\red255\green255\blue255;\red0\green0\blue0;\red255\green255\blue255;}
\deftab720
\pard\pardeftab720\partightenfactor0
\f0\fs22 \cf2 \cb3 \expnd0\expndtw0\kerning0
\outl0\strokewidth0 \strokec2
}{\rtf1\ansi\ansicpg1252{\fonttbl\f0\fnil\fcharset0 ArialMT;}
{\colortbl;\red255\green255\blue255;\red0\green0\blue0;\red255\green255\blue255;}
\deftab720
\pard\pardeftab720\partightenfactor0
\f0\fs22 \cf2 \cb3 \expnd0\expndtw0\kerning0
\outl0\strokewidth0 \strokec2
}{\rtf1\ansi\ansicpg1252{\fonttbl\f0\fnil\fcharset0 ArialMT;}
{\colortbl;\red255\green255\blue255;\red0\green0\blue0;\red255\green255\blue255;}
\deftab720
\pard\pardeftab720\partightenfactor0
\f0\fs22 \cf2 \cb3 \expnd0\expndtw0\kerning0
\outl0\strokewidth0 \strokec2
}[url=https://servimg.com/view/17916191/77][im. Thanks for all the help aluminum covers with dry cork did the trick.
Tom77- Donating Member
- Street Cred : 9
Re: 383 in and running. Now the question?
by dynchel Sun 18 May 2014 - 7:32
Looks nice. 
 And just in time for show season.  H3ll theres one about half a mile away that starts at noon. 
 And just in time for show season.  H3ll theres one about half a mile away that starts at noon.Â
dynchel- Donating Member
- Street Cred : 40
Re: 383 in and running. Now the question?
by chevellelaguna Sun 18 May 2014 - 17:38
Looks great! Must run awesome. Those edelbrock foam filters are a huge restriction.
chevellelaguna- G3GM Enthusiast
- Street Cred : 16
77mali- Donating Member
- Street Cred : 62
Re: 383 in and running. Now the question?
by Dinomyte Sun 18 May 2014 - 20:39
Nice motor look sharp . .
Dinomyte- Donating Member
- Street Cred : 11
thatfnthing- Donating Member
- Street Cred : 65
G3GM :: G3 :: General Discussion
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum|
|
|
» 76 Laguna parked in 2002
» El Camino/Sprint LH Aftermarket Quarter Panel FOR SALE
» dashes
» Thanks for having me
» 77 elco SS
» 3-g cars in Finland
» Stainless brake lines
» New chassis for my 73
» 1973 Chevelle SS, 350, 4spd. build