Brake line questions
+2
dynchel
pila
6 posters
Page 1 of 1
Brake line questions
So while changing my front springs the caliper fell pulling on the brake line and broke it. Since I have to replace the line I thought maybe I'd do them all. Should I go stainless? Is it worth it on a limit use car that sits in a heated garage when not in use. Also I have a Wilwood adjustable proportional valve. I bought it when I bought my disc brake rear end. I haven't installed the rear end yet but I still may. Should I toss the original valve and use this one? Thoughts?
bitterfitter- Donating Member
- Street Cred : 9
Re: Brake line questions
Valve is up to you. I went regular steel lines. Anytime you have two dissimilar metals you get cross corrosion. And the steel ones lasted more than 40 years
Joe73- Donating Member
- Street Cred : 83
Re: Brake line questions
Good point on the corrosion. I hate bending stainless vs mils steel anyways.
I would like to do the valve in case I ever put the other disc brakes on the back.
Any idea if the lines are all one size? Say 3/16" maybe.
I would like to do the valve in case I ever put the other disc brakes on the back.
Any idea if the lines are all one size? Say 3/16" maybe.
bitterfitter- Donating Member
- Street Cred : 9
Re: Brake line questions
I don't recall. But I bought mine from in linetube.com. Check their site.
Joe73- Donating Member
- Street Cred : 83
Re: Brake line questions
Joe, I think that is inlintube.com They have pre-bent lines ,hoses etc, and located in the Detroit area.
I used steel lines, and painted them, before & after installing them, except the lines running up the the MC, which are stainless, that they sent by mistake !!
I used steel lines, and painted them, before & after installing them, except the lines running up the the MC, which are stainless, that they sent by mistake !!
pila- Donating Member
- Street Cred : 43
Re: Brake line questions
Your right Bill. I was typing on my phone and it wouldnt put all the letters together for some reason. LOL.
HAPPY NEW YEAR !!!!
HAPPY NEW YEAR !!!!
Joe73- Donating Member
- Street Cred : 83
Re: Brake line questions
Since replacing brake lines is part of my job I'm used to making my own. There is a nice ez bend line that is copper I believe, very easy to work with and won't rust. Should be available at Napa stores
dynchel- Donating Member
- Street Cred : 40
Re: Brake line questions
Thanks for the heads up about the brake line materials. I will check that out.
bitterfitter- Donating Member
- Street Cred : 9
Re: Brake line questions
So while I am working on the brakes, I figured I may just replace all the worn out parts on my ride. Â I have new rotors, rubber hoses, pads for the front. Â The rears have already been done from brake cylinder to hardware and shoes.
I have replaced my master cylinder already,but now would like to replace my booster and possibly the proportioning valve with new ones. Â Any suggestions where to find these and anything to watch out for? Â It appears there are a few different shape, size boosters out there. Â Would like to find one like the original. Â Same with the proportioning valve.
I have replaced my master cylinder already,but now would like to replace my booster and possibly the proportioning valve with new ones. Â Any suggestions where to find these and anything to watch out for? Â It appears there are a few different shape, size boosters out there. Â Would like to find one like the original. Â Same with the proportioning valve.
bitterfitter- Donating Member
- Street Cred : 9
Re: Brake line questions
I purchased my valve from Inline tube and everything was correct. Info is in this thread.
https://www.g3gm.com/t7561-proportioning-valve-questions
Not sure about brake booster.
https://www.g3gm.com/t7561-proportioning-valve-questions
Not sure about brake booster.
Hawk03- G3GM Enthusiast
- Street Cred : 18
Re: Brake line questions
With the proportioning valve, keep an eye on the way the brake wire hooks up. Thats where the differences usually are. Ours is a stud.
Joe73- Donating Member
- Street Cred : 83
Re: Brake line questions
How did the Inline tube stuff line up? Was it pretty plug and play as far as fitment?
brownbomber77- G3GM Member
- Street Cred : 4
Re: Brake line questions
All the lines I have bought from them go on like factory pieces. I used to work at a Corvette shop here and we got all our stuff from them. I would usually go down there and pick it up. Very nice setup they have. I have been through the place and seen the machines in action a few times. Amazing....
bitterfitter- Donating Member
- Street Cred : 9
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Yesterday at 10:21 pm by lagunaman
» door interior trim retainer clips
Yesterday at 8:29 pm by Limey SE
» Rusty's progress motor Parts arrived LOL Half are on
Yesterday at 12:25 pm by bracketchev1221
» Painting Interior Plastic
Thu Apr 25, 2024 11:52 am by Joe73
» Anyone good at photoshop?
Wed Apr 24, 2024 9:37 pm by 76 Malibu
» El Camino/Sprint LH Aftermarket Quarter Panel FOR SALE
Wed Apr 24, 2024 5:18 am by relic7680
» 1973 chevelle four speed console
Sun Apr 21, 2024 10:32 pm by Limey SE
» dashes
Sun Apr 21, 2024 10:26 pm by Limey SE
» Used OEM Hood 73-77
Fri Apr 19, 2024 2:46 pm by 73 ss wgn
» 76 Laguna parked in 2002
Sun Apr 07, 2024 1:32 pm by Limey SE