Passenger side seat belt buckle - swivel buckets
2 posters
G3GM :: Classifieds :: Wanted
Page 1 of 1
Passenger side seat belt buckle - swivel buckets
i am looking for the passenger side seat belt buckle from a swivel bucket seat car. would prefer in black, but wont necessarily rule out any other colors. If anyone has one that they are willing to part with, i would greatly appreciate it. Thank you.
Silverblack73ss- G3GM Newbie
- Street Cred : 0
Re: Passenger side seat belt buckle - swivel buckets
Again...as was the case with lagunaman's request earlier today for a driver side belt...may I ask exactly what it is you need?
When you say you need a buckle and then mention you prefer black, are you wanting the entire retractor assembly; complete with the outer plastic covers? Or, are you repairing an existing one and only need the strap w/buckle?
When you say you need a buckle and then mention you prefer black, are you wanting the entire retractor assembly; complete with the outer plastic covers? Or, are you repairing an existing one and only need the strap w/buckle?
Mcarlo77- Donating Member
- Street Cred : 77
Re: Passenger side seat belt buckle - swivel buckets
The retractor and belt portion is good, i just need the strap with buckle. it has a blue GM logo on to push to disengage and bolts below the console and wrapped in a rigid plastic. I dont need the entire seat belt assembly, just the buckle part.
did that make sense? otherwise i could get pictures i think.
did that make sense? otherwise i could get pictures i think.
Silverblack73ss- G3GM Newbie
- Street Cred : 0
Re: Passenger side seat belt buckle - swivel buckets
Oh, okay...you're needing the inner receiver belt. Understandable, as the rigid plastic on the '73's is almost always brittle, cracked/broken and distorted from age; especially, at the base where it covers the mtg bolt.
If you're not concerned with it being absolutely "correct", you can use those supplied on '74-'77, too. Only difference is GM used a more flexible plastic sheath; although they didn't hold up a whole lot better (usually split at the top). I do have a couple of the '74-'77 style...but, they are split as described.
If you're not concerned with it being absolutely "correct", you can use those supplied on '74-'77, too. Only difference is GM used a more flexible plastic sheath; although they didn't hold up a whole lot better (usually split at the top). I do have a couple of the '74-'77 style...but, they are split as described.
Mcarlo77- Donating Member
- Street Cred : 77
Similar topics
» Seat belts for swivel buckets
» WTB: 73-77 A Body passenger side bucket seat slides
» Driver side seat belt retractor
» WTB: 73-77 A Body passenger side bucket seat slides
» Driver side seat belt retractor
G3GM :: Classifieds :: Wanted
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Today at 5:02 pm by Matchstx
» 1973 4 door laguna frame same as 1973 2 door chevelle
Today at 4:56 pm by Matchstx
» Dash assembly for 73-77 Malibu/Monte/El Camino,etc.
Today at 2:48 pm by Limey SE
» Window louvers
Today at 12:47 pm by JCervantes10
» 1973 Chevelle SS 1 Family
Wed May 08, 2024 8:11 am by Mitchell Murphy
» 1973 Chevelle SS, 350, 4spd. build
Wed May 08, 2024 8:09 am by Mitchell Murphy
» Who works on 73-77 "soft" steering wheels?
Tue May 07, 2024 12:46 pm by relic7680
» Blue door jamb sticker
Sun May 05, 2024 3:10 pm by Joe73
» Factory am/fm
Sun May 05, 2024 6:22 am by Joe73
» Factory am/fm
Sat May 04, 2024 11:15 pm by 77camino