MONTE FRONT BUMPER TUCK
+15
Limey SE
77mali
Showtime73
DaveFury
tropdeprojet
74Malibu383
orange Juiced
KC77Monte
dynchel
driveit
impalamonte
LS_Quest
Mcarlo77
1973 454 MONTE
thatfnthing
19 posters
G3GM :: Media :: G3 Project Pictures
Page 2 of 2
Page 2 of 2 • 1, 2
Re: MONTE FRONT BUMPER TUCK
looks really good. Did you cut the bumpers where they run along the fenders on the outside?
Roadcaptain S3- Donating Member
- Street Cred : 26
Re: MONTE FRONT BUMPER TUCK
Nope I have 1 inch clearance, bumper to fender. I had to trim the flexible fillers though.
77cruiser- G3GM Member
- Street Cred : 0
Re: MONTE FRONT BUMPER TUCK
I like that a lot Never seen it done on a Monte ( IIRC ) looks great
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 97
Re: MONTE FRONT BUMPER TUCK
Thinking about doing the back too. I can only go in a little over an inch on back.
77cruiser- G3GM Member
- Street Cred : 0
Re: MONTE FRONT BUMPER TUCK
There is a 73 Monte on the internet ive seen before. The guy used a first gen.bumper. dont know how he did it but it looked really good.
ant7377- G3GM Addict
- Street Cred : 36
Re: MONTE FRONT BUMPER TUCK
77cruiser wrote:Nope I have 1 inch clearance, bumper to fender. I had to trim the flexible fillers though.
Did you just trim the fillers along that front edge that sits under the bumper?
Or did you have to cut back further?
Roadcaptain S3- Donating Member
- Street Cred : 26
Re: MONTE FRONT BUMPER TUCK
Just trimmed to match the profile of the bumper, there's room for error.
77cruiser- G3GM Member
- Street Cred : 0
Re: MONTE FRONT BUMPER TUCK
OK...probably starting this soon, wasn't sure where to trim.
I did get an extra set of corners just in case.
Did you have to cut the center piece as well?
I did get an extra set of corners just in case.
Did you have to cut the center piece as well?
Roadcaptain S3- Donating Member
- Street Cred : 26
Re: MONTE FRONT BUMPER TUCK
Roadcaptain S3 wrote:OK...probably starting this soon, wasn't sure where to trim.
I did get an extra set of corners just in case.
Did you have to cut the center piece as well?
I'll be looking out for your pics to see how it turns out. I was told to just remove the center section on my 75 Malibu but I would have to trim the edges. That makes me kind of nervous.
Damon23- G3GM Member
- Street Cred : 5
Page 2 of 2 • 1, 2
Similar topics
» Why you should NEVER EVER, EVER tuck in your Malibu's front bumper
» 74 Malibu bumper tuck
» 73 chevelle front bumper?
» 74 Malibu bumper tuck
» 73 chevelle front bumper?
G3GM :: Media :: G3 Project Pictures
Page 2 of 2
Permissions in this forum:
You cannot reply to topics in this forum
Sat May 18, 2024 1:56 pm by REVINKEVIN / Mr. 600+HP
» Pate Swap Meet - Texas Motor Speedway - G3 Parts Goldmine
Sat May 18, 2024 12:20 pm by g3chevy / Mr Pontiac
» '73 Laguna coupe - factory 454- SoCal $2500
Fri May 17, 2024 4:38 pm by Mcarlo77
» Dash Solutions
Fri May 17, 2024 3:22 pm by 76 Malibu
» Rusty's progress Done stuff again LOL
Thu May 16, 2024 12:56 pm by Limey SE
» 1973 4 door laguna frame same as 1973 2 door chevelle
Tue May 14, 2024 4:39 pm by chevelleman
» Anyone good at photoshop?
Mon May 13, 2024 12:50 pm by 76 Malibu
» '77 Monte Carlo Landau - Parting out - 61k miles on car
Fri May 10, 2024 5:02 pm by Matchstx
» Dash assembly for 73-77 Malibu/Monte/El Camino,etc.
Fri May 10, 2024 2:48 pm by Limey SE
» Window louvers
Fri May 10, 2024 12:47 pm by JCervantes10