rebuilding door hinges
5 posters
rebuilding door hinges
I rebuilt the door hinges for my El Camino project. The usual pin & bushings of course, but I needed to do the roller that engages the spring-loaded detent to hold the door open.
With the spring removed, I discovered that the shaft that the roller runs on, is pressed in place, and it has splines on it. Clamping the shaft in the vice, I tapped the hinge to remove the splined shaft.
Then I found that the hole the shaft was pressed into, was the right size for a 5/16-24 tap, so I tapped the hole, and used a bolt with an un-threaded shank that was the correct amount for a bushing, which the roller will run on. I used an aircraft bolt, since I have those in stock.
Anyway, just a bit of info for anyone who may want to re-do door hinges.....
With the spring removed, I discovered that the shaft that the roller runs on, is pressed in place, and it has splines on it. Clamping the shaft in the vice, I tapped the hinge to remove the splined shaft.
Then I found that the hole the shaft was pressed into, was the right size for a 5/16-24 tap, so I tapped the hole, and used a bolt with an un-threaded shank that was the correct amount for a bushing, which the roller will run on. I used an aircraft bolt, since I have those in stock.
Anyway, just a bit of info for anyone who may want to re-do door hinges.....
pila- Donating Member
- Street Cred : 43
Re: rebuilding door hinges
ok now I will you send you mine to do and you keep them, then you send me yours that are done LOL No really
Limey SE- Management
- Street Cred : 97
Re: rebuilding door hinges
@ Limey. Good info! I'll add this to the 1,000,000 things left to do on my car
DiscoMalibu- G3GM Member
- Street Cred : 7
Re: rebuilding door hinges
Don't suppose there might be a photo or two of that?
thatfnthing- Donating Member
- Street Cred : 65
Re: rebuilding door hinges
i just found my rollers were shot,but still working.
so i found a pass,side but had to replace the pin and bushing.but the roller was near new.
the driver i found needed nothing,roller looked new also.
so i found a pass,side but had to replace the pin and bushing.but the roller was near new.
the driver i found needed nothing,roller looked new also.
Last edited by 1973 454 MONTE on Thu Apr 25, 2013 2:26 pm; edited 1 time in total
1973 454 MONTE- Donating Member
- Street Cred : 36
Re: rebuilding door hinges
Here's a pic. did I ever tell ya I like red ?
pila- Donating Member
- Street Cred : 43
Re: rebuilding door hinges
Thanks. My bushings are in decent shape, but my passenger door is actually missing the detent pin altogether, so this info will come in handy when I eventually get to that point.
thatfnthing- Donating Member
- Street Cred : 65
Similar topics
» Door Hinges
» Rebuillding my door hinges
» Trade NOS A-body trunk lid hinges for 1974 Monte Carlo trunk lid hinges.
» Rebuillding my door hinges
» Trade NOS A-body trunk lid hinges for 1974 Monte Carlo trunk lid hinges.
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Yesterday at 7:44 pm by Joe73
» Blue door jamb sticker
Yesterday at 7:41 pm by Joe73
» 1973 Chevelle SS 1 Family
Yesterday at 3:45 pm by Limey SE
» Painting Interior Plastic
Yesterday at 1:48 pm by 76Chevelle2Tone
» Need driver side bucket seat 73 Laguna
Tue Apr 30, 2024 9:44 pm by Limey SE
» triangle stainless window trim
Sun Apr 28, 2024 2:04 pm by 454fourspeedss
» door interior trim retainer clips
Sat Apr 27, 2024 8:29 pm by Limey SE
» Rusty's progress motor Parts arrived LOL Half are on
Sat Apr 27, 2024 12:25 pm by bracketchev1221
» Anyone good at photoshop?
Wed Apr 24, 2024 9:37 pm by 76 Malibu
» El Camino/Sprint LH Aftermarket Quarter Panel FOR SALE
Wed Apr 24, 2024 5:18 am by relic7680