Found a camshaft!!!
3 posters
G3GM :: G3 Tech :: Engine & Driveline
Page 1 of 1
Found a camshaft!!!
So after a few weeks of research, I've decided to go with the Edelbrock Torker camshaft.
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5027209-P_1279_N%7CGRP60011____
I know I need to get a new timing chain, springs, and pushrods, and here's what I've found:
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5027527-P_166_N%7CGRP60010____
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5020131-P_173_N%7CGRP60011____
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__22342651-P_3049_N%7CGRP60011____
I've got a discount code for $50 off purchases over $150 through Advance Auto, so I'm splitting it up into two orders, so essentially getting $375 worth for $275. Does anyone know of anything else that would need to be purchased that I might be forgetting? (I already have a 4 bbl Edelbrock carb I plan on reusing and am going to get a new intake manifold a little later down the road)
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5027209-P_1279_N%7CGRP60011____
I know I need to get a new timing chain, springs, and pushrods, and here's what I've found:
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5027527-P_166_N%7CGRP60010____
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5020131-P_173_N%7CGRP60011____
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__22342651-P_3049_N%7CGRP60011____
I've got a discount code for $50 off purchases over $150 through Advance Auto, so I'm splitting it up into two orders, so essentially getting $375 worth for $275. Does anyone know of anything else that would need to be purchased that I might be forgetting? (I already have a 4 bbl Edelbrock carb I plan on reusing and am going to get a new intake manifold a little later down the road)
wokrdan AKA BU Balls- G3GM Member
- Street Cred : 2
Re: Found a camshaft!!!
What pistons are you using ? The compression ratio will need to be above 9 or so to 1, or that cam will not perform. You may want to email or call Edelbrock or even Summit Racing tech line, before buying that one. If you have stock 8.5 to 1 CR, that's too much cam I believe, and will not add much or any power.
pila- Donating Member
- Street Cred : 43
Re: Found a camshaft!!!
IF YOUR RUNNING AN AUTO TRANS. YOU'LL NEED A 2200-2500 STALL CONVERTOR, TIMING GEAR SET DOES NOT MATTER ( HEADS UP ON THE MARKS THOUGH) IF I WERE YOU I'D STEP UP ON THE SPRING PRESSURE BY 100, HYD. TAPPET CAMS LIKE THAT IF YOU WON'T TO BE ABLE TO REV..?????????????!!!!!!!!!!!!!!wokrdan AKA BU Balls wrote:So after a few weeks of research, I've decided to go with the Edelbrock Torker camshaft.
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5027209-P_1279_N%7CGRP60011____
I know I need to get a new timing chain, springs, and pushrods, and here's what I've found:
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5027527-P_166_N%7CGRP60010____
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__5020131-P_173_N%7CGRP60011____
http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product__22342651-P_3049_N%7CGRP60011____
I've got a discount code for $50 off purchases over $150 through Advance Auto, so I'm splitting it up into two orders, so essentially getting $375 worth for $275. Does anyone know of anything else that would need to be purchased that I might be forgetting? (I already have a 4 bbl Edelbrock carb I plan on reusing and am going to get a new intake manifold a little later down the road)
2fat2fly- Donating Member
- Street Cred : 2
G3GM :: G3 Tech :: Engine & Driveline
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Sat May 18, 2024 1:56 pm by REVINKEVIN / Mr. 600+HP
» Pate Swap Meet - Texas Motor Speedway - G3 Parts Goldmine
Sat May 18, 2024 12:20 pm by g3chevy / Mr Pontiac
» '73 Laguna coupe - factory 454- SoCal $2500
Fri May 17, 2024 4:38 pm by Mcarlo77
» Dash Solutions
Fri May 17, 2024 3:22 pm by 76 Malibu
» Rusty's progress Done stuff again LOL
Thu May 16, 2024 12:56 pm by Limey SE
» 1973 4 door laguna frame same as 1973 2 door chevelle
Tue May 14, 2024 4:39 pm by chevelleman
» Anyone good at photoshop?
Mon May 13, 2024 12:50 pm by 76 Malibu
» '77 Monte Carlo Landau - Parting out - 61k miles on car
Fri May 10, 2024 5:02 pm by Matchstx
» Dash assembly for 73-77 Malibu/Monte/El Camino,etc.
Fri May 10, 2024 2:48 pm by Limey SE
» Window louvers
Fri May 10, 2024 12:47 pm by JCervantes10