Rear sway bar
5 posters
Page 1 of 1
Rear sway bar
I bought a 9C1 rear sway bar for my 75 Malibu. I know I have to remove the trailing arms to drill for the bracket holes. Anyone have the measurements for the holes? Thanks.
Damon23- G3GM Member
- Street Cred : 5
Re: Rear sway bar
I will be out with Car this weekend here if no One else chimes in and get measurement's Damon will be 47 degrees and getting a Jump Start on Interior Removal for the New going in, WOOT WOOT Bite me Mother Nature and I am having your Groundhog on the grill As well B***H
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 97
Re: Rear sway bar
If you support the frame, put a jack under a rear shock and take out the lower shock bolt. You can lower the rear to make enough room to drill it. No need to remove the arm.
Joe73- Donating Member
- Street Cred : 83
Re: Rear sway bar
I'll look when I get home, I've got a drawing I found from Hellwig I think when I did this that was very helpfull.
Dinomyte- Donating Member
- Street Cred : 11
Re: Rear sway bar
clanceman427 wrote:Here is the photo:
That will get you the rear bolt sir. From there just measure forward for the front bolt.
fasrnur- G3GM Enthusiast
- Street Cred : 9
Re: Rear sway bar
I've looked high and low for what I thought I had. This is the only document I can find on the Hellwig site and it's not correct, for the previous generation
http://www.ecklerschevelle.com/assets/pdf/chevelle/608576.pdf
Sorry Damon23, I'll keep looking if you still need it
As soon as I posted this I found what I was looking for.
https://static.summitracing.com/global/images/instructions/HEL-5803.pdf
It's not exactly what you're looking for but it's what I used to get the factory holes located in the right spot for my LCA that didn't have holes for sway bar inserts, then bolted in the inserts I'd gotten from John M. and the 1" 9c1 bar I had.
hope this helps...
http://www.ecklerschevelle.com/assets/pdf/chevelle/608576.pdf
Sorry Damon23, I'll keep looking if you still need it
As soon as I posted this I found what I was looking for.
https://static.summitracing.com/global/images/instructions/HEL-5803.pdf
It's not exactly what you're looking for but it's what I used to get the factory holes located in the right spot for my LCA that didn't have holes for sway bar inserts, then bolted in the inserts I'd gotten from John M. and the 1" 9c1 bar I had.
hope this helps...
Dinomyte- Donating Member
- Street Cred : 11
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Yesterday at 8:12 pm by 76Chevelle2Tone
» Rusty's progress motor Parts arrived LOL Half are on
Yesterday at 2:56 pm by Limey SE
» Painting Interior Plastic
Thu Apr 25, 2024 11:52 am by Joe73
» Anyone good at photoshop?
Wed Apr 24, 2024 9:37 pm by 76 Malibu
» El Camino/Sprint LH Aftermarket Quarter Panel FOR SALE
Wed Apr 24, 2024 5:18 am by relic7680
» 1973 chevelle four speed console
Sun Apr 21, 2024 10:32 pm by Limey SE
» dashes
Sun Apr 21, 2024 10:26 pm by Limey SE
» Used OEM Hood 73-77
Fri Apr 19, 2024 2:46 pm by 73 ss wgn
» 76 Laguna parked in 2002
Sun Apr 07, 2024 1:32 pm by Limey SE
» Thanks for having me
Wed Mar 27, 2024 7:25 pm by 77camino