saginaw 800
5 posters
Page 1 of 1
saginaw 800
I decided to try and overhaul my first steering box. It started leaking from both seals. I started out with the seals and one thing led to another and ended up overhauling the whole thing. I figured if I screw it up or get in over my head I could always slap it back together and turn it in for a core. Got it installed today and after bleeding the system it turned out great. no leaks, no noise. The biggest pia of the whole thing was the 24 balls inside. Those of you wanting to try I suggest taking it apart on a cookie sheet or something to contain the balls when it comes apart. Also you will want to get a GM service manual. The box is from a 85 Monte SS. 12.7 ratio high effort. I borrowed a 85 buick service manual. Very detailed instructions inside as well as the proper way to adjust. My 73 service manual does not cover any of it. You also need a needle type inch pound wrench to measure the drag. Total cost was $40. I didn't think to take any pics while it was apart. There are also several useful you-tube vids on this.
$20 for the kit
$10 for a spanner wrench.
$10 paint & cleaners.
$20 for the kit
$10 for a spanner wrench.
$10 paint & cleaners.
73ss- G3GM Enthusiast
- Street Cred : 11
Re: saginaw 800
Nice job. That needle inch pound torque wrench is also needed when setting pinion load on the rear diff. Good to have.
Joe73- Donating Member
- Street Cred : 83
Re: saginaw 800
Great to hear you did it yourself. Not many folks would wade into a steering gear like you did !
I just bought an exchange rebuilt gear box for the wife's Jeep from hell, to replace the old one.....
I just bought an exchange rebuilt gear box for the wife's Jeep from hell, to replace the old one.....
pila- Donating Member
- Street Cred : 43
Re: saginaw 800
Thanks Guys...For an everyday driver such as the jeep, probably better off to get a reman one due to the down time. I had all winter to play with this one. Although some of this reman stuff is hit or miss nowadays..
I was also worried about getting something out of sync and having the steering wheel off center. It turns out everything is keyed and clocked so that it only goes together one way. Can't really screw that part of it up..
I was also worried about getting something out of sync and having the steering wheel off center. It turns out everything is keyed and clocked so that it only goes together one way. Can't really screw that part of it up..
73ss- G3GM Enthusiast
- Street Cred : 11
Re: saginaw 800
Nice job, looks brand new! Curious if you remember what size the nut was to remove the pitman arm?
Thanks.
Thanks.
77mali- Donating Member
- Street Cred : 62
Re: saginaw 800
77mali wrote:Nice job, looks brand new! Â Curious if you remember what size the nut was to remove the pitman arm?
Thanks.
Thanks.. 1 5/16"
73ss- G3GM Enthusiast
- Street Cred : 11
Similar topics
» 73 SS Saginaw M20 reverse lockout rod tracings here
» Anyone near Wilmington, Illinois need a free saginaw 4 speed ??
» Anyone near Wilmington, Illinois need a free saginaw 4 speed ??
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Today at 2:04 pm by 454fourspeedss
» Need driver side bucket seat 73 Laguna
Today at 12:36 am by Limey SE
» door interior trim retainer clips
Yesterday at 8:29 pm by Limey SE
» Rusty's progress motor Parts arrived LOL Half are on
Yesterday at 12:25 pm by bracketchev1221
» Painting Interior Plastic
Thu Apr 25, 2024 11:52 am by Joe73
» Anyone good at photoshop?
Wed Apr 24, 2024 9:37 pm by 76 Malibu
» El Camino/Sprint LH Aftermarket Quarter Panel FOR SALE
Wed Apr 24, 2024 5:18 am by relic7680
» 1973 chevelle four speed console
Sun Apr 21, 2024 10:32 pm by Limey SE
» dashes
Sun Apr 21, 2024 10:26 pm by Limey SE
» Used OEM Hood 73-77
Fri Apr 19, 2024 2:46 pm by 73 ss wgn