grant quick release hub
3 posters
grant quick release hub
what quick release do i need?
they have a few that i know it cant be but i dont know what ones it is out of these.
:Pinless Quick Steering Wheel Disconnect Kit, Weld-On Hub For 3/4'' Shaft, Fits Grant Steering Wheel w/ 3 Hole Bolt Pattern
:Pin Type Quick Steering Wheel Disconnect Kit, GM Splined Shaft, Fits Grant Steering Wheel w/ 3 Hole Bolt Pattern
:Pinless Quick Steering Wheel Disconnect Kit, GM Splined Shaft, Fits Grant Steering Wheel w/ 3 Hole Bolt Pattern
:Pinless Quick Steering Wheel Disconnect Kit, Weld-On Hub For 5/8'' Shaft, Fits Grant Steering Wheel w/ 3 Hole Bolt Pattern
http://www.jegs.com/p/Grant/Grant-Quick-Release-Hubs/748405/10002/-1
they have a few that i know it cant be but i dont know what ones it is out of these.
:Pinless Quick Steering Wheel Disconnect Kit, Weld-On Hub For 3/4'' Shaft, Fits Grant Steering Wheel w/ 3 Hole Bolt Pattern
:Pin Type Quick Steering Wheel Disconnect Kit, GM Splined Shaft, Fits Grant Steering Wheel w/ 3 Hole Bolt Pattern
:Pinless Quick Steering Wheel Disconnect Kit, GM Splined Shaft, Fits Grant Steering Wheel w/ 3 Hole Bolt Pattern
:Pinless Quick Steering Wheel Disconnect Kit, Weld-On Hub For 5/8'' Shaft, Fits Grant Steering Wheel w/ 3 Hole Bolt Pattern
http://www.jegs.com/p/Grant/Grant-Quick-Release-Hubs/748405/10002/-1
coreys73chevelle- G3GM Senior Member
- Street Cred : 8
Re: grant quick release hub
was going to get this kit but i dont know if it will fit
http://www.jegs.com/i/Grant/470/673K/10001/-1
http://www.jegs.com/i/Grant/470/673K/10001/-1
coreys73chevelle- G3GM Senior Member
- Street Cred : 8
Re: grant quick release hub
I have a non-tilt colunm but might get tilt someday. i took off my wheel and its 3 small bolts and a large nut in the center.
coreys73chevelle- G3GM Senior Member
- Street Cred : 8
Re: grant quick release hub
corey if its saveable i can hook you up with limeys tilt column floor shift steering column
___________________________________________
1977 Chevelle SE x2
One Mild original
one Wild NON original
Anthony
Limey SE- Management
- Street Cred : 97
Re: grant quick release hub
470-3001 is what I would get if I were looking to get one of those.
A lot of these are weld on application, so once you install it you pretty much can't go back very easily.
A lot of these are weld on application, so once you install it you pretty much can't go back very easily.
bigredlaguna- G3GM Senior Member
- Street Cred : 53
Re: grant quick release hub
Limey wrote:corey if its saveable i can hook you up with limeys tilt column floor shift steering column
not right now. im going to get it running and the floor shifter and seats in then see where im at. im getting a little ahead of myself if i get anything right now besides seats, and shifter
coreys73chevelle- G3GM Senior Member
- Street Cred : 8
Similar topics
» Barry Grant is closing its doors for good .
» quick little video of my car.
» What Retains the Hood Release Handle?
» quick little video of my car.
» What Retains the Hood Release Handle?
Permissions in this forum:
You cannot reply to topics in this forum
|
|
Yesterday at 10:51 am by Mcarlo77
» 1973 Chevelle SS, 350, 4spd. build
Yesterday at 10:10 am by Joe73
» Five Decades?
Yesterday at 8:23 am by Iggy
» cluster metal trim
Sun Mar 17, 2024 8:02 pm by 76Chevelle2Tone
» 1977 Olds 442 in MN
Sun Mar 17, 2024 12:11 pm by g3chevy / Mr Pontiac
» Nos wheel well moldings
Sat Mar 16, 2024 9:58 pm by Limey SE
» Dual Dash Speaker Setup (Sent out and gone now)
Fri Mar 15, 2024 4:09 pm by fasrnur
» Rusty's progress Hood sorta Finalized and other Updates
Fri Mar 15, 2024 1:51 pm by bracketchev1221
» speedometer pointer bouncing
Wed Mar 13, 2024 10:27 pm by 76Chevelle2Tone
» WANTED 73-77 Chevelle 442 rear window louvers
Wed Mar 13, 2024 2:52 pm by Limey SE